Rudder Bushing
Rudder Bushing
does anyone know a source for the nylon/plastic ? rudder bushings (top & bottom ) on a C-20 ?
thanks,
jerry
thanks,
jerry
- clair hofmann
- Posts: 221
- Joined: Sun Apr 10, 2005 6:20 pm
- Location: S.E.Pa / Inner banks NC
I don't have a source for a pre made bushing , but there is a source for plastics if you need to make one.
www.mcmastercarr.com. They have all types of plastics... nylon, delrin, UHMWP, etc.
good luck
clair
www.mcmastercarr.com. They have all types of plastics... nylon, delrin, UHMWP, etc.
good luck
clair
-
- Posts: 2
- Joined: Thu Apr 10, 2014 12:45 am
- Location: South Ozone Park, NY 11420-2831 718-641-0724
I do not have any idea of the source of rubber and nylon bushing.But I can say something about polyurethane bushing.As this is long lasting heat resistance and water resistance.
Last edited by richardsrow on Sat Apr 12, 2014 3:14 am, edited 1 time in total.
- EmergencyExit
- Site Admin
- Posts: 2956
- Joined: Wed Dec 10, 2003 5:02 pm
- Location: Mississippi Gulf Coast
Check www.idasailor.com. Click on Chryslers at the left and scroll down a bit. They list them for $39 each.
-
- Site Admin
- Posts: 146
- Joined: Sat Oct 02, 2010 3:06 am
- Location: Norfolk
- Capt. Bondo
- Site Admin
- Posts: 713
- Joined: Thu Aug 20, 2009 8:08 am
- Location: Hudson, WI
Thanks EE for the link, but now I'm confused
I thought the bushing and the through hull was all the same thing?
Now I see the bushing are seperate.
What would be the correct through hull to use, the part the big hose connects to?
Any one have a picture or illistration of the proper assembly of the rudder shaft through the hull?
I thought the bushing and the through hull was all the same thing?
Now I see the bushing are seperate.
What would be the correct through hull to use, the part the big hose connects to?
Any one have a picture or illistration of the proper assembly of the rudder shaft through the hull?
H:)ppy Place
78 Chrysler 22
You can go to a Zen Master or you can go Sailing, either way you end up in about the same place..... a Happy Place
78 Chrysler 22
You can go to a Zen Master or you can go Sailing, either way you end up in about the same place..... a Happy Place
- EmergencyExit
- Site Admin
- Posts: 2956
- Joined: Wed Dec 10, 2003 5:02 pm
- Location: Mississippi Gulf Coast
Here is my video explanation of the replacement upper rudder bearing and lower thru hull rudder bearing for the C22 https://www.youtube.com/watch?v=P8i_MKp ... ature=plcp
The drawings are in the documents section for the C22.
The drawings are in the documents section for the C22.
Bill
- EmergencyExit
- Site Admin
- Posts: 2956
- Joined: Wed Dec 10, 2003 5:02 pm
- Location: Mississippi Gulf Coast
I just read about a repair that one of the Columbia guys did. It involved taking it apart, coating everything with vaseline, and reassembling. You then totally immobilize the rudder and inject thickened West epoxy into the area. It worked for him. Instructions are on the West site I think.
Tom
1981 Endeavour 43 s/v Pearl Lee
Former 1976 Columbia Payne 9.6 s/v Gin Rhumby
Former 1979 Chrysler 26, s/v Copacetic
http://www.asswhaffleyachtclub.net
http://www.svpearllee.com
1981 Endeavour 43 s/v Pearl Lee
Former 1976 Columbia Payne 9.6 s/v Gin Rhumby
Former 1979 Chrysler 26, s/v Copacetic
http://www.asswhaffleyachtclub.net
http://www.svpearllee.com